Diode Dynamics 3157 HP11 LED (Pair)
This bulb has four 1.5W chips around the sides, to fill in the light's housing and give a great appearance and full look, and one 5W LED chip with a projector lens on top to project outward. It uses an 3157-size durable inject-molded terminal and will fit as a replacement for stock halogen. It uses less power and heat than halogen bulbs, and will last longer, with its engineered aluminum heat-sinking technology. A component is embedded to prevent blowing the LED from voltage surge, and a diode is implanted to protect the LED from reverse polarity. The LED is wired for 12V operation, the kind found on all vehicles.
Included in your order is TWO BULBS.
These LEDs are available in a crisp, bright, amber or red color.
Lumens: BUYER BEWARE! Most sellers just provide "calculated" lumen numbers, based on the maximum potential brightness of the LED chips on the bulb. For example, if a bulb has five 10-lumen chips, they will rate it at 50 lumens. However, this is not accurate, as the design of an LED bulb does not get rid of heat fast enough to run the LEDs at maximum.
These "calculated" lumen ratings are much, much higher than the true, measured light output, so it will look like competitors' bulbs are brighter than ours. This is because Diode Dynamics does not provide inflated "calculated" numbers; we believe it is misleading. We test the actual brightness of the bulbs in our lab, to provide real lumen output measurements. Our measurements are accurate, but they are usually much lower than the misleading "calculated" figures.
LED Components. Diode Dynamics uses only the highest quality LED chips in the production of its bulbs. This means we use only brand-name suppliers such as Epistar, Cree, Osram, and Samsung.
While our bulbs may look the same as others on the market, most copycat bulbs use economy-grade LED chips in order to reduce costs. This greatly reduces the reliability and overall brightness of the bulb when you compare it to Diode Dynamics.
Construction. Although LED technology allows for extremely long bulb life, the market is flooded with cheap LED bulbs that fail prematurely due to inferior construction. The worst enemy of LEDs is excessive heat, and when bulbs are not designed properly, they do not disperse heat as well, leading to premature failure.
Off-brand, cheap bulbs exhibit poor solder uniformity, high levels of flux in the solder, uneven chip placement, low-gauge terminal wires, poor assembly, and bulbs held together with inferior adhesives. At best, solder joints will crack and fail on low-quality LEDs after a few weeks of use. In the worst case, these bulbs can damage housings as the extra flux and adhesive evaporates and creates a residue on the lens of the housing.
Diode Dynamics bulbs are produced with modern, computerized equipment, and only the best materials, to ensure complete uniformity, high quality, and long bulb life.
The turn signals on most vehicles will begin to blink fast (hyperblink) when LED bulbs are installed. This is because the new LEDs will use less power than the original bulbs, so your vehicle thinks that the bulb is out and warns you by hyperblinking.
This phenomenon will be the same for every LED bulb on the market- there is no such thing as a "no hyperblink" LED bulb, even though some companies advertise them as such.
Flasher Replacement: Replacing the flasher relay, the module that controls blinking speed, is the easiest option to correct hyperblinking. You can remove the flasher on your vehicle, which is a small relay module under the dash, and replace it with a new flasher designed for LEDs. You will only need one flasher for your vehicle, whether you are replacing just one pair or both sets of turn signal bulbs (front/rear).
Resistor Kit: If you prefer not to change the flasher, you can add resistors to the bulb's circuit, and mimic the power consumption of the original bulb, returning the vehicle to normal turn signal speed. Resistors are a universal fix for any vehicle. Our resistors are 50w, 6 ohm, and come with extra-long connection wires for easy install. If you have both front and rear LED turn signals, you should purchase one set for each pair, to create enough resistance for the whole turn signal circuit. The installation itself takes only 10-15 minutes, and involves making two simple connections. Everything you need is included in the kit.